1

00:00:00,800 --> 00:00:03,933

Hello everyone, today we will learn about the vertical control area

2

00:00:03,933 --> 00:00:06,666

and software buttons in the oscilloscope panel

3

00:00:09,633 --> 00:00:12,000

Let's take a look at the software button first

4

00:00:12,400 --> 00:00:15,900

The software button refers to the row of buttons around the screen

5

00:00:16,233 --> 00:00:20,933

For example, if I want to change the automatic trigger mode to the normal trigger mode,

6

00:00:21,300 --> 00:00:23,100

I can click this button

7

00:00:26,200 --> 00:00:30,066

Press the button next to the slope to change the rising edge and falling edge

8

00:00:32,666 --> 00:00:35,733

Second, this is the print and store button

9

00:00:37,666 --> 00:00:41,600

When the green light is on, press this button to store the waveform

10

00:00:45,000 --> 00:00:49,233

When the light is off, we press this button, it is the printing function

11

00:00:50,000 --> 00:00:55,433

The third button, this is the probe detection button, this function is generally rarely used

12

00:00:56,900 --> 00:01:00,200

Fourth, this is the probe compensation contact point

13

00:01:02,266 --> 00:01:07,366

When calibrating the probe, you need to place the probe on the probe compensation contact point

14

00:01:07,366 --> 00:01:09,333

to adjust the probe compensation

15

00:01:14,366 --> 00:01:17,966

The fifth is the USB interface, used to connect the U disk

16

00:01:20,366 --> 00:01:26,333

Next, let's take a look at the function introduction of some buttons and knobs in the vertical control area

17

00:01:26,733 --> 00:01:30,966

The first small knob, this is the vertical position adjustment of channel 1

18

00:01:31,633 --> 00:01:35,000

The current position of channel 1 is at the middle 0 position

19

00:01:35,366 --> 00:01:40,500

By adjusting this knob, the vertical position of channel 1 can be moved up and down

20

00:01:43,200 --> 00:01:47,566

The second small knob, this is the vertical position adjustment of channel 2

21

00:01:51,133 --> 00:01:53,733

The third is the opening and closing of channel 1,

22

00:01:54,100 --> 00:01:56,733

and it is also the menu setting of channel 1

23

00:01:59,466 --> 00:02:03,700

After pressing this button, you can see the setting menu of channel 1

24

00:02:11,733 --> 00:02:17,466

This CH2 is the opening and closing of channel 2, and it is also the menu setting of channel 2

25

00:02:22,133 --> 00:02:26,466

The button in the middle is a vertical menu, which is generally not used

26

00:02:28,333 --> 00:02:32,066

The sixth big knob is the volts/ grid adjustment of channel 1

27

00:02:35,966 --> 00:02:38,766

The current channel 1 is set to 1V per grid

28

00:02:40,333 --> 00:02:44,200

The seventh big knob is the volts/ grid adjustment of channel 2

29

00:02:44,900 --> 00:02:47,733

The current channel 2 is set to 1V per grid

30

00:02:48,666 --> 00:02:53,666

The 8th and 9th, respectively are channel 1 and channel 2 probe input terminals,

31

00:02:54,100 --> 00:02:56,333

used to connect oscilloscope probes

32

00:02:57,333 --> 00:03:02,333

Ok, here's an introduction to the oscilloscope's vertical control area and software buttons